[tiger777]

Прошил прошивкой WL500gp-1.9.2.7-d-r1612M-max_mad-(29.06.10)- сделал сброс подсоединил 3G ZTE MF637 к ASUS WL-500 GP , прописал через телнет следующее
[admin@(none) root]$ nvram set wan_usb_standard=1
[admin@(none) root]$ nvram set wan_usb_username=
[admin@(none) root]$ nvram set wan_usb_passwd=
[admin@(none) root]$ nvram set wan_usb_port=0
[admin@(none) root]$ nvram set wan_usb_speed=921600
[admin@(none) root]$ nvram set wan_usb_apn= internet.life.com.by
[admin@(none) root]$ nvram set wan_usb_dialnumber=*99#
[admin@(none) root]$ nvram set wan_usb_vend
[admin@(none) root]$ nvram set wan_usb_prod
[admin@(none) root]$ nvram set wan_usb_mtu=1492
[admin@(none) root]$ nvram set wan_usb_mru=1492
[admin@(none) root]$ nvram set wan_usb_zerocd="-v 0x19d2 -p 0x2000 -M 55534243123456782000000080000c85010101180101010101 000000000000"
[admin@(none) root]$ nvram commit
[admin@(none) root]$ modem
В результате получил малевича с таким логом
Jan 1 02:00:04 kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan 1 02:00:04 kernel: Vendor: ZTE Model: USB SCSI CD-ROM Rev: 2.31
Jan 1 02:00:04 kernel: Type: CD-ROM ANSI SCSI revision: 02
Jan 1 02:00:07 kernel: usb.c: registered new driver acm
Jan 1 02:00:07 kernel: acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters (patched)
Jan 1 02:00:07 admin: <<<< Driver acm installed >>>>
Jan 1 02:00:07 admin: <<<< Start script modem. >>>>
Jan 1 02:00:07 admin: <<<< Test options. >>>>
Jan 1 02:00:07 admin: <<<< umts/hsdpa modem set. >>>>
Jan 1 02:00:07 admin: <<<< All required options was set >>>>
Jan 1 02:00:07 admin: <<<< Success ... Go on ... >>>>
Jan 1 02:00:07 admin: <<<< Compat. delay was not set. >>>>
Jan 1 02:00:08 admin: <<<< USB-modem 0x19d2:0x2000 >>>>
Jan 1 02:00:09 kernel: USB device disconnected from the SCSI subsystem
Jan 1 02:00:09 kernel: usbdevfs: process 219 (usb_modeswitch) did not claim interface 0 before use
Jan 1 02:00:14 kernel: usb.c: USB disconnect on device 01:03.2-2 address 2
Jan 1 02:00:19 kernel: hub.c: new USB device 01:03.2-2, assigned address 3
Jan 1 02:00:20 kernel: scsi1 : SCSI emulation for USB Mass Storage devices
Jan 1 02:00:20 kernel: Vendor: ZTE Model: MMC Storage Rev: 2.31
Jan 1 02:00:20 kernel: Type: Direct-Access ANSI SCSI revision: 02
Jan 1 02:00:20 kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Jan 1 02:00:20 kernel: sda: Waiting for disc 0 to settle.
Jan 1 02:00:23 kernel: sda: Unit Not Ready, sense:
Jan 1 02:00:23 kernel: Info fld=0x0, Current 00:00: sns = f0 2
Jan 1 02:00:23 kernel: ASC=3a ASCQ= 0
Jan 1 02:00:23 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Jan 1 02:00:23 kernel: sda : READ CAPACITY failed.
Jan 1 02:00:23 kernel: sda : status = 1, message = 00, host = 0, driver = 08
Jan 1 02:00:23 kernel: Info fld=0x0, Current sd00:00: sns = f0 2
Jan 1 02:00:23 kernel: ASC=3a ASCQ= 0
Jan 1 02:00:23 kernel: Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Jan 1 02:00:23 kernel: sda : block size assumed to be 512 bytes, disk size 1GB.
Jan 1 02:00:23 kernel: Partition check:
Jan 1 02:00:23 kernel: /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:00, sector 0
Jan 1 02:00:23 kernel: I/O error: dev 08:00, sector 0
Jan 1 02:00:23 kernel: unable to read partition table
Jan 1 02:00:24 admin: <<<< USB-modem 0x19d2:0x0031 after usb_modeswitch >>>>
Jan 1 02:00:24 kernel: usb.c: registered new driver serial
Jan 1 02:00:24 kernel: usbserial.c: USB Serial support registered for Generic
Jan 1 02:00:24 kernel: usbserial.c: Generic converter detected
Jan 1 02:00:24 kernel: usbserial.c: Generic converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
Jan 1 02:00:24 kernel: usbserial.c: Generic converter detected
Jan 1 02:00:24 kernel: usbserial.c: Generic converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
Jan 1 02:00:24 kernel: usbserial.c: Generic converter detected
Jan 1 02:00:24 kernel: usbserial.c: Generic converter now attached to ttyUSB2 (or usb/tts/2 for devfs)
Jan 1 02:00:24 kernel: usbserial.c: USB Serial Driver core v1.4
Jan 1 02:00:26 admin: <<<< USB-modem with ZeroCD find and set. >>>>
Jan 1 02:01:16 admin: <<<<Failed to set the PIN code or open Modem Port.>>>>
Jan 1 02:01:17 wan: connected manually
Jan 1 02:01:20 wan: connected manually
Jan 1 02:01:27 wan: connected manually
Jan 1 02:01:29 wan: connected manually
в чем причина помогите пож перепробовал все прошивки которые есть не могу никак соединить данный девайс китайский с ASUS?
Я несилен в английском но перевел так
Не удалось установить код PIN или открыть Порт модема .>>>> пин код отключен, почему не открывает???????